Sending a Payload

• The latest release of TegraRcmGUI (either the MSI or zip)
• A USB-A to USB-C cable (or a standard USB-C cable if your computer natively supports USB-C)

Payloads you'll need for this guide:

• The latest release of Hekate. The Hekate payload (hekate_ctcaer bin) is located in the hekate_ctcaer zip.
• The latest release of TegraExplorer.

1. Install and run TegraRcmGUI.
2. Navigate to the Settings tab, then press Install Driver and follow the on-screen instructions.
   • If you face issues when installing the driver, follow the driver installation with Zadig section below.
3. Connect your Switch in RCM to your PC using the USB cable.
4. Navigate to the Payload tab of TegraRcmGUI.
   • Your Switch should be shown as detected in the bottom left corner.
5. Press the file button next to Inject payload, and navigate to and select your payload .bin file.
   • The first time you read this page you should inject TegraExplorer.bin.
6. Click Inject payload to launch the payload you selected.

Follow these steps if you face issues when installing the driver with TegraRcmGUI. You will need the latest version of Zadig.

1. Launch Zadig. In the Options menu, be sure that List All Devices is enabled.
2. Connect your Switch in RCM to your PC using the USB cable.
3. In Zadig, select "APX" in the device list.
4. Select libusbK (v3.1.0.0) in the driver list.
5. Click Install Driver and wait for the installation to finish.

• The latest release of fusee-interfacee-tk
• A USB-A to USB-C cable (or a standard USB-C cable if your computer natively supports USB-C)

Payloads you'll need for this guide:

• The latest release of Hekate. The Hekate payload (hekate_ctcaer bin) is located in the hekate_ctcaer zip.
• The latest release of TegraExplorer

1. Download and run the payload injector (if you're on Linux, you will need to run this program as root, use sudo, or follow the instructions at Linux injection without root).
2. Connect your Switch in RCM to your PC using the USB cable.
3. Wait for your Switch to be shown as found in the injector.
4. Press Select Payload, and navigate to and select your payload .bin file.
   • The first time you read this page you should inject TegraExplorer.bin.
5. Click Send Payload! to launch the payload you selected.

• The latest release of Rekado
  • You will need to enable Unknown Sources in your device settings to install this
• A USB-C cable
  • If your device has a USB-C port, you may use a C-C cable
  • If your device only has a Micro USB port, you will need a USB OTG adapter and a USB A-C cable
    • This will not work on every phone!

Payloads you'll need for this guide:

• The latest release of Hekate. The Hekate payload (hekate_ctcaer bin) is located in the hekate_ctcaer zip.
• The latest release of TegraExplorer

1. Copy the hekate_ctcaer .bin file from the Hekate .zip file to a location on your phone.
   • A tool such as Amaze File Manager can do this.
2. Launch Rekado on your phone.
3. Navigate to Payloads, then press the + button at the bottom right.
4. Navigate to your hekate_ctcaer .bin file and tap it to add it to Rekado's menu.
5. Optional, but recommended: Navigate to Rekado's settings and enable Hide bundled.
6. Connect your Switch in RCM to your phone using the USB cable.
7. If prompted, grant Rekado access to the Switch.
8. Select your payload .bin file in the dialog that pops up.
   • The first time you read this page you should inject TegraExplorer.bin.

• A USB-C cable
• If your chromebook has a USB-C port, do note that this will not work using a C-C cable.

Payloads you'll need for this guide:

• The latest release of Hekate. The Hekate payload (hekate_ctcaer bin) is located in the hekate_ctcaer zip.
• The latest release of TegraExplorer

1. Go to the injection website and scroll all the way down
2. Select the "Upload Payload" option and upload the hekate_ctcaer .bin file from the Hekate .zip file.
   • The first time you read this page you should inject TegraExplorer.bin.
3. Connect your Switch in RCM to your Chromebook using the USB cable.
4. Select "Do the thing". A pop up will appear. Click the APX option.
5. Press the Connect button and the payload will be injected.